Use this cable to retain an original fitment camera when fitting a new head unit.

For Fiat, Alfa Romeo, Lancia and other Fiat Chrysler group vehicles built after 2014 with original reverse camera.

This camera retention adapter allows you to retain your factory reverse camera when installing an aftermarket stereo in a wide range of VW, Skoda, and SEAT vehicles. The cable connects into the new Quadlock harness used for the new aftermarket head unit, and a separate reverse feed is required to activate the camera on the new screen. InCarTec CANbus interfaces (49-VW-01, 49-VW-02, 49-VW-05) provide this reverse signal. With plug-and-play installation and broad compatibility, this adapter ensures seamless integration and preserves your vehicle’s original safety features.

Allows you to retain an original reverse camera from a Mercedes factory fitted Audio 20 or COMAND head unit when fitting an after-market radio.

PLEASE NOTE: This cable is only compatible with single fakra connections. Double fakra connections are not supported.

Use this cable to retain an original fitment camera when fitting a new head unit.

For Chrysler, Dodge, Jeep and RAM cars and trucks with original equipment reverse camera.

Use this cable to retain an original fitment camera when fitting a new head unit.

For General Motors, Chevrolet, Cadillac and GMC 2012 onwards cars and trucks with original equipment navigation and reverse camera.

Retention camera interface allowing you to retain/ keep the factory OEM fitted reverse view camera on selected Suzuki and Izuzu cars, when replacing with a new aftermarket head unit.

This interface is compatible with all touch screen models from 2012 onwards.

Allows you retain the original OEM camera on mostly Japanese Domestic Market model Toyotas with 6v rear camera.

Suitable for original head units with 4 pin camera connector.

PLEASE NOTE: European and Japanese spec cars often have different head units - if your model was sold in both markets, please check the connections before ordering

Retain original Camera on Highline Volkswagen, Seat and Skoda cars with Volkswagen RNS510, RNS315, RCD510, Seat Trinax and Skoda Bolero or Columbus head units.

This Camera interface runs from the original camera module, located elsewhere in the car to the back of the new radio.

Only for highline cars with moving guide lines and a white display in the Multi function display.

PLEASE SEE LONG DESCRIPTION FOR FULL COMPATIBILITY

Use this cable to retain an original fitment camera when fitting a new head unit. Comes with 12v to 6v voltage adapter.

Also for Subaru cars with original 7" screen built from 2015 onwards

Retain original Camera on Ford Transit Euro 5/6  (With small 4.2 inch screen)

This Camera interface cable allows you to retain the original factory fitted camera when fitting an aftermarket head unit on Ford Transit Euro 5 and Euro 6 models (With the smaller 4.2 inch screen display)

PLEASE NOTE: ONLY SUITABLE FOR FORD TRANSIT EURO 5/ EURO 6 MODELS WITH SMALLER 4.2 INCH DISPLAY) 

This camera retention interface allows you to retain the factory-fitted reverse camera on Honda vehicles from 2015 onwards that came without a factory touchscreen radio. Designed for seamless integration, it connects the OEM camera to an aftermarket head unit, preserving rear-view visibility and safety features. Ideal for installers upgrading factory audio systems while maintaining OEM functionality.

This adapter cable includes a 12V DC to 6V DC voltage converter to provide a suitable power supply to a cars original parking camera.

PLEASE NOTE: Only suitable for select Honda (2015 Onwards) vehicles Without Touchscreen

Drops 12V DC to 6V DC to provide a suitable power supply to a cars original parking camera.

Use with camera retention interfaces that do not have a voltage dropper built in.

PLEASE NOTE: This is not a camera interface. If you are looking to add or retain a camera please visit our car specific camera interface range

Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Toyota (2012 Onwards) car models (Display and navigation model radios only).

This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.

PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671 

Retention camera interface allowing you to retain/ keep the factory OEM fitted reverse view camera on select Kia and Hyundai car models, when replacing with a new aftermarket head unit.

This interface is compatible with various Kia and Hyundai car models with an original factory fitted AVN head unit with a 24pin connection.

Allows you retain the original OEM camera on Toyota Aygo, Peugeot 108 and Citroen C1

Suitable for original head units with 8 pin camera connector.

PLEASE NOTE: Suitable for cameras from original fitment X-Touch and X-Nav head units

Retention camera interface allowing you to retain/ keep the factory OEM fitted reverse view camera on select Ford vehicles with SYNC 2 (8 Inch) or SYNC 3 systems.

When fitting an aftermarket head unit, this t-harness cable uses a 54 pin connector which connects to the back of the vehicles OEM SYNC system to retain the original reverse view camera on the screen.

PLEASE NOTE: Vehicle Coding is required with Forscan to enable RVC function on Sync systems

This retention interface allows you to keep the factory reverse camera working when upgrading to an aftermarket head unit in a Honda Civic/CR-V (2012-2017). It connects directly to the OEM connector so there’s no need to cut factory wires. Designed to deliver the camera feed seamlessly via RCA output, this cable lets you retain safety features while installing your new stereo.

PLEASE NOTE: designed for used with our steering wheel control interfaces with reverse trigger output.

Allows you retain the original OEM camera on multiple Mitsubishi models.

Suitable for original head units with 8 pin Grey camera connectors.

Toyota 2019 onward reverse camera retention interface allowing use of the original reverse camera with a new aftermarket head-unit.

Retains original reverse camera, includes handbrake output.

See full description for compatible cars and compatibility notes.

Allows you retain the original OEM camera on a Honda 2VN0 navigation system when installing a new aftermarket head unit.

Suitable for 2VN0 units with a Green 7 Pin connector

PLEASE NOTE: For 2VN0 Navigation Systems only. Please check connections in instructions for compatibility  

Allows you retain the original OEM camera on a Honda 2VN3 navigation system when installing a new aftermarket head unit.

Suitable for 2VN3 units with 7 and 8 pin Grey connectors.

PLEASE NOTE: For 2VN3 Navigation Systems only. Please check connections in instructions for compatibility  

Retain original Camera on Volkswagen and Skoda cars with an RGB camera

This Camera interface cable allows you to retain the original factory fitted camera when fitting an aftermarket head unit on various Volkswagen and Skoda vehicle models

PLEASE SEE LONG DESCRIPTION FOR FULL COMPATIBILITY

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface for Toyota RAV4 cars allowing use of original buttons with a new aftermarket head-unit.

This interface will retain the use of the steering wheel audio controls with an aftermarket head unit, as well as retaining the use of the original OEM camera.

Suitable for Toyota Alphard (2002 - 2008) and RAV4 (2006 - 2012) vehicle models.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface and ISO cables allowing use of original buttons with a new aftermarket head-unit.

This interface will retain the use of the steering wheel audio controls with an aftermarket head unit, as well as retaining the use of the original OEM camera.

Suitable for Subaru vehicle models (2007-2013) with original Kenwood Navigation head unit.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit.

This interface also retains the use of the 360 panoramic camera system and provides outputs for parking brake, speed pulse and reverse gear.

Suitable for various Toyota models from 2014-2019

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit.

This interface also retains the use of the 360 panoramic camera system and provides outputs for parking brake, speed pulse and reverse gear.

Suitable for Toyota RAV4 (2019 Onwards) with amplified sound systems

This Mitsubishi steering wheel control and 360° camera retention interface is designed for the following vehicles: Montero Sport (QE) 2016–2019, Pajero Sport IV (QE) 2015–2019, and Shogun Sport (QE) 2016–06/2019. It allows the retention of factory audio steering wheel buttons and the 360° camera display when installing an aftermarket stereo. The interface connects to standard ISO wiring and works with compatible head units to preserve steering wheel control functions and OEM camera visuals for a professional, feature-complete installation.